10×12 shed plans, gambrel shed. Plans include a free PDF download (link at bottom of blog post), illustrated instructions, material list with shopping list and cutting list.
Shed Plans – 10×12 Gambrel Shed – Overview
10×12 Shed Plans -Gambrel Shed – Material List
Shopping List
Shopping List
Floor
9 – pressure-treated 2×6 – 12′
2– pressure-treated 2×6 – 10′
4– pressure-treated 4×4 – 10′
4 – 3/4″ tongue and groove plywood – 4’x8′ sheet
Wall Frames
6– 2×4 – 12′
6– 2×4 – 10′
46 – 2×4 – 8′
Rafters / Truss
25– 2×4 – 8′
Siding
15 – t1-11 exterior siding – 4’x8′ sheet
Front / Back Roof Trim
4 – 2×4 – 8′
Roof Deck
8– 1/2 plywood – 4’x8′ sheet
Corner Trim / Side Trim
12– 1×4 – 8′
Hardware
shingles
roofing felt
roof staples
roof tacks
drip edge
3 1/2″ galvanized nails
1 1/4″ galvanized finishing nails
3″ galvanized finishing nails
2″ galvanized nails
2″ deck screws
door hinges
door handle
Cutting List
Cutting List
Floor
2 – pressure-treated 2×6 – 10′
9 – pressure-treated 2×6 – 11′ 9″
4– pressure-treated 4×4 – 10′
4 – 3/4″ tongue and groove plywood – 4’x8′ sheet (cut to size)
Wall Frames
4– 2×4 – 10′
2 – 2×4 – 9′ 5″
46– 2×4 – 7′ 6″
4– 2×4 – 11′ 5″
2 – 2×4 – 12′
Rafters / Truss
40 – 2×4 – 3′ 9 7/8″ (22.5 angle cuts on ends opposite direction)
5– 2×4 – 8′ (cut to size)
Siding
15– t1-11 exterior siding – 4’x8′ sheet (cut to size)
Front / Back Roof Trim
8– 2×4 – 3′ 9 7/8″ (22.5 angle cuts on ends opposite direction)
Roof Deck
8– 1/2″ plywood – 4’x8′ sheet (cut to size)
Corner Trim / Side Trim
12– 1×4 – 8′ (cut to size)
The 10×12 gambrel shed floor is built with pressure treated 2×6’s and pressure treated 4×4’s.
Nail 3 1/2″ nails through the 2×6 band and into the floor joist. Floor joist are 16″ O.C.
Attach the 10′ long 4×4 pressure treated skids to the bottom of the floor frame. Square out the floor frame by measuring diagonally until both sides measure the same. Secure the 4×4 skids by nailing 3 1/2″ nails through the floor frame and into the 4×4 skids.
Cut to size and install the 3/4″ tongue and groove plywood for the floor deck. Secure the floor plywood with 2″ deck screws. Screw through the plywood and into the floor frame.
Front and back wall frames. The shed wall frame is built using 2×4’s.
The wall studs are 16″ O.C.
Assemble the back wall frame as shown on illustration above (see illustration below for close up view ).
The front wall frame will have a door and, for instructions on framing the dooror window see the pages below:
- Shed Door Plans
- Wall Framing – Adding a Shed Window
Assemble the front and back wall frame using 3 1/2″ nails.
Illustration above shows a close up look of the front and back wall frame ends.
Cut the 2×4’s as shown on illustration above for the side walls.
Wall studs are 16″ O.C.
Assemble the side wall frame using 3 1/2″ nails.
The illustration above shows details for the shed truss.
The shed roof truss is built using 2×4’s.
Cut the 2×4’s as shown on illustration above. The truss are assembled using 1/2″ plywood gussets. Nail 2″ nails through the gusset and into the rafters.
Attach the roof truss to the shed, the roof truss will be spaced out 16″ O.C. Toenail 3 1/2″ nails through the roof truss and into the wall frame.
Cut 2×4’s to size, notch the top around rafters, see illustration above.
Cut the t1-11 exterior siding and install using 1 1/4″ finishing nails.
Cut and install the front and back 2×4 roof trim as shown on illustration above. Use clamps to hold the trim in place, use 3″ finishing nails to install the 2×4 trim.
Measure, cut, and install the 1/2″ plywood for the roof deck using 2″ nails. Nail through the roof deck and into the roof truss frame.
Install the side and corner trim as shown on illustration using 2″ finishing nails.
Install roofing felt, drip edge, and shingles.
Like these 10×12 gambrel shed plans? Let me know, leave me a comment below. Share this link with your friends and your social media, thanks.
PDF DOWNLOAD
- Shed Plans – 10×12 Gambrel Shed – PDF Download
Download
- Shed Plans 10×12 Gable Shed – PDF Download
Download
- 10×12 Barn Shed Plans – PDF Download
Download
Related Articles
Push Stick Templates | Free Plans | PDF Download
DIY co*ckatiel Nesting Box
DIY Double Chair Bench With Table
DIY 2×4 Planter Box | How To Plans
DIY 2-in-1 Bird House and Feeder
8×8 Pergola Plans
40 comments
Jake
July 8, 2016 at 9:40 am
Shed floor measures 10×12. Shed measures 10′ 2 3/4″ x 12′ 2 3/4″ with siding and trim.
Reply
Jason Boyd
September 11, 2020 at 1:42 pm
What’s a rough cost using the shopping guide?
Reply
John ward
November 14, 2016 at 11:04 am
What happened to the 10×12 gambrel roof shed that used 2×6 lumber for the rafters, and had optional front overhang
Reply
Dave
December 9, 2016 at 10:18 pm
I have the same question, what happened to the prior shed plans that used 2×6 lumber for the rafters, and had optional front overhang? I am in the middle of building it and needed some reference material.
Reply
Robert fuller
March 10, 2017 at 9:43 am
Inice look for 12 by 16 plans
Reply
GARY Whited
May 21, 2017 at 12:59 pm
not sur of 2×4 block trim, and trim/roof intersection, shingls bow out on trim piece or stop at trim, not understanding that part
Reply
Jim Perry
June 11, 2017 at 7:24 am
Just built this shed, thanks for the great plans. We used post-to-beam brackets to attach the gambrels, and added joist hangars around them to run 2×6 joists across 2/3s of the length to create loft storage. The only real point of confusion is the interface between the roof and the sides, which we dealt with by just having the roof overhang by a couple of inches. Thanks!
Reply
Rodney Bish
October 28, 2017 at 6:04 pm
What should the measurement be at the bottom of the rafters point to point? I assumed it would be 10 feet, but mine came up 3 inches short?
Reply
Dan
January 29, 2018 at 8:27 am
All these plans look great anyway i could request plans for a 12 x 16 with loft?
Reply
Danny Windon
December 11, 2020 at 8:17 pm
I got the 12 x 16 shed plans …. do you offer it in a barn style
Reply
Len
February 17, 2018 at 2:09 pm
These plans are perfect, just what I was looking for. THANK YOU SO MUCH!
Reply
Patrick Smith
April 5, 2018 at 1:50 pm
Is there enough plywood in this material list to make the gussets and spacers?
Reply
mithhtl
June 27, 2018 at 5:20 am
WARNING: Do not use these plans if this is your first time building a shed. SO MUCH is left out. We used these plans and are up to the point of putting the roof on. Notice that the walls are 12′ long exactly but the graphic shows being able to use a 2×4 on either end for trim and have the plywood cover the 2×4 trim. This is impossible considering you only have 12 foot of plywood to use. (one 4×8 sheet and half of a 4×8 sheet). There is so much left out of this. How does the roofing sheeting go on? How does the drip edge go on? How does the trim go on? I thought that we could just “figure it out” as we went along but it has caused so much headaches not having a complete plan. It’s hard enough to get a project like this finished in your spare time let alone a project with incomplete plans. The roof is the most important part too, it’s what keeps your stuff DRY which is the whole point of a SHED (to SHED water).
Reply
Ryan
December 21, 2018 at 3:12 pm
They are FREE plans. If you’ve never built a shed or don’t have general measuring and building knowledge, you should probably spend money on COMPLETE plans. Otherwise these plans worked just fine.
Reply
Jeremy
May 22, 2019 at 1:15 pm
Love the response Ryan. Much cleaner than I was thinking
Reply
Jim Johns
May 2, 2020 at 1:49 pm
Not for a novice builder, I wouldn’t complain, they were nice enough t share free plans!!!
Reply
Jason Boyd
September 11, 2020 at 1:07 pm
What’s a rough cost using the shopping guide?
Reply
Jamie
October 25, 2020 at 8:20 pm
In my location at Menards, approximately $2,800.00 to $3,000.00.
Reply
Dave Smith
July 10, 2018 at 4:15 pm
So, after having looked at the plans you should have a 6″ over lap on both roof ends as well as all of the roof trusses in over the side walls in order to put on trim and a drip edge on both side walls. You will need to lengthen the top of the roof trusses accordingly while keeping the 22.5 degree angle. Just cut your upper floor supports to length from 2x6x12’s instead of 2X6x10’s. However you will need to measure and cut supports for the area with no upper floor. That can be achieved by attaching notched 2×4 / 2×6 lumber to come down from the center area of the upper truss area to the over lap the lower ends of the trusses overhang. Don’t forget to trim and use the angles properly to fit this whole overhang properly. This area must be closed giving you a soffit to attach guters and trim to. Also, build small ladder frames to attach the building end supports over the top of the wall siding and it will finish the look for the shed, and don’t forget to finish that soffit area as well. Also, I would put a would put a drip rail, 3 to 6 inches wide and 6 inches past the side of the doors to keep that door frame as dry as possible.
Reply
Jeffrey Smith
January 8, 2019 at 10:12 pm
Where are my 10×12 Barn Shed Plans!
Reply
Construct101
January 8, 2019 at 11:47 pm
Check your email, it might have gone to your spam, if it’s not their email me so I can email them to you, thanks.
Reply
Sarah Young
January 12, 2019 at 6:46 am
I did not receive them, either, or for the porch swing, firewood shed. I checked spam & promotions folders, nothing in either. I also noticed there was no option for me to put in my email when requesting the download, but when I click on download, it says thank you & that a pdf will arrive in my email. But how could it when there was no option to put in my address?
Reply
Pam Mariner
April 23, 2019 at 2:12 pm
looking for plans and material list on a 12’x20′ high barn style storage shed.
Reply
DelGavio
June 1, 2019 at 6:02 pm
Great plans. Built these to store 6 motorcycles. I did modify one of the 10′ wide ends and installed a 7′ wide garage door for easier entry.
Thanks!Reply
pierre
June 25, 2019 at 7:10 am
Good morning
I`m looking for a 12 x 14 Gambrel shed planReply
stephen
October 3, 2019 at 10:17 pm
whats the cost roughly with this plan, as in for all the materials?
Reply
Jamie
October 25, 2020 at 8:22 pm
$2,800.00 to $3,000.00
Reply
Timothy Travis
October 10, 2019 at 10:02 am
Got a question. I want to do this but the max height I can go is 11ft 6in . I looked over the plans I think I can cut 2 feet out one foot from the walls and one ft from the bottom of the roof. Any advice would be great.
Reply
Thurman Blacka
March 2, 2020 at 12:43 pm
How do I obtain the complete building plans for the Gambrel shed
Reply
Brandon Beale
April 28, 2020 at 11:33 am
I found a website that is very helpful with the rafters and how to tie them in. You can select overhang (or not) and gussets and it creates a template for you. Made the roof/wall tie in a lot less puzzling that some others have commented on.
Otherwise, these plans are awesome. Thank you very much!
Reply
Jennifer
May 15, 2020 at 11:31 am
Hi I would really like those she’d plans but I want to add windows and an extra door I don’t think it would be much different right than your plans.
Thank you Jen 😊Reply
Thomas Kinney
November 30, 2020 at 11:20 am
Are you still offering the free 10 X 12 Gambrel Shed plans and if so My info is bellow. I like the shed and I know there are a few mods that can be done to personalize it. Thanks guys.
Reply
Jamie Gisby
March 22, 2021 at 7:17 pm
I finished the lower half of the 10×12 lofted shed and am now putting together the rafters it seems that when i put them together each section is a bit different how close do they have to be
Reply
Mark Antony Mace
November 16, 2021 at 5:00 am
Hi All
From the UK so bear with me, I dont want the free plans, are there plans that are 100% complete that I can pay for ??
I have a fair bit of building knowledge , but would prefer 100% complete plans as i will be buiulding this from heavy hardwood and its expensive so dont want to find issues once i start building
thanks in advance
Reply
Adrian Kampschnieder
March 25, 2022 at 8:30 am
do you have plans for a 10×14 gambrel shed?
Reply
barbara
March 12, 2023 at 5:46 pm
hola buenas noches, no puedo descargar los planos, no me permite hacer clic donde dice descargar. Gracias
Reply
Scott Acopulos
July 14, 2023 at 9:57 am
Thanks
Reply
Logan Beckstrom
July 17, 2023 at 6:19 am
Just finished this shed. couple things to note that we found along the way – as mentioned previously.. plan to leave an overhang on your roof to install drip edge. the front and back (10′ walls) are fine, but where the angled roof meets up is a pain to get drip edge installed on.. save yourself the hassle and add an overhang (I have no major construction experience to provide on how this can be accomplished sadly…)
Another thing… for your studs on the walls… ADD 1-1/2″…. (instead of 7′ – 6″… cut your studs to 7′ – 7-1/2″) The reason I say this.. is the walls will then measure out to the 96″ needed to use full sheets of plywood on the interior… as the plan lays out, your inside walls measure out to 94-1/2″… meaning we have to shave that bit off each sheet..
Reply
Will Case
October 14, 2023 at 5:15 pm
What is the inside height of the gambrel roof?
Reply
